BOZONLI M18 Lengthen Hex Bolt - Fully Threaded Setscrew Stainless Steel Mechanical Bolts M18×30mm,1 pcs

Product Information

By approximately ignoring the corner rounding for a perfect hexagon the relation of the distance across points s' and the distance across flats s is s' = s / cos(30°) = 1.1547⋅ s. Minimum and maximum spacing p 1, p 2 and edge distances e 1, e 2 for bolts are given in EN1993-1-8 Table 3.3. The minimum values are: e 1≥ 1.2 d 0, e 2≥ 1.2 d 0, p 1≥ 2.2 d 0, p 2≥ 2.4 d 0, where d 0 is the diameter of the hole, e 1, p 1 are measured parallel to the load transfer direction and e 2, p 2 are measured perpendicular to the load transfer direction. The design shear resistance of bolts F v,Rd as given in EN1993-1-8 Table 3.4 is only valid when the bolt is used in holes with nominal clearance not exceeding the values given in the standard EN 1090-2 'Requirements for the execution of steel structures', as specified in EN1993-1-8 §3.6.1(4). For typical coarse pitch thread bolts the standard sizes are: M3, M3.5, M4, M5, M6, M7, M8, M10, M12, M14, M16, M18, M20, M22, M24, M27, M30, M33, M36, M39. The following table provides examples of clearance hole sizes, standard or coarse thread pitches along with fine thread pitches and their corresponding tapping hole sizes. Metric clearance and tapping drill hole sizes. Size

They are designated as above also including the pitch of thread in mm e.g. M8 × 1, M14 × 1.5, M27 × 2 etc. where e 2 is the distance between the center of the edge bolt and the end of the plate measured perpendicular to the load transfer direction, p 2 is the distance between the centers of neighboring bolts measured perpendicular to the load transfer direction, and d 0 is the diameter of the bolt hole. The tensile stress area depends on the thread and it can be calculated according to ISO 898-1 Section 9.1.6.1.class- stamp/meter/account (Including Royal Mail Signed For ® sent as 1st class) Online Postage, Articles for the Blind The tensile stress area A s corresponds to the reduced cross-sectional area inside the threaded part of the bolt. Albania, Andorra, Belarus, Bosnia and Herzegonia, Ceuta, Faroe Island, Gibraltar, Greenland, Guernsey. Iceland, Jersey, Kosovo, Liechenstein, Macedonia, Moldova, Montenegro, Norway, Russia, San Marino, Serbia, Switzerland, Turkey, Ukraine Therefore, based on the equations above, the bearing resistance of the bolt F b,Rd is not affected by the distances e 1, p 1, e 2, p 2 when the following conditions are satisfied:

d m is the mean of the across points and across flats dimensions of the bolt head or the nut, whichever is smaller.Bulgarian, Croatia, Cyprus, Estonia, Hungary, Latvia, Lithuania, Malta, Romania, Slovakia, Slovenia The calculated strength properties for coarse pitch thread bolts may be used conservatively for fine pitch thread bolts. According to EN1993-1-8 § 3.6.1(4) the design shear resistance F v,Rd should only be used where the bolts are used in holes with nominal clearances not exceeding those for normal holes as specified in EN 1090-2 'Requirements for the execution of steel structures'. Nuts and bolts are essential fastenings, critical in the safe assembly of machinery, equipment, furniture and much more. In most circumstances, it’s absolutely vital that the right size of fastening is used. In this brief guide we provide an introduction to standard ISO metric sizes for nuts and bolts which will hopefully help dispel any confusion. BS3643 Parts 1&2